Underlay fleece PREMIUM Pack I 15 m², quality 500 g/m²
58,08 €
Very strong, thermally and mechanically bonded, rot-proof underlay fleece for protecting the pool liner from PVC-incompatible materials, min. 500 g/m². Recommended for the following swimming pools from our range: Round pools 3.00 m, Round pools 3.50 m, Round pools 3.60 m. The fleece is supplied in rolls 2 m wide and 7.5 m long. Due to manufacturing and packaging reasons, the fleece cannot always be supplied in one piece; a maximum of two sections will be provided.
SKU:
270544
Category: New products
Description
Non-rotting underlay fleece for protecting the pool liner. Minimum quality: 500 g/m².
Additional information
| Weight | 7,5 kg |
|---|
Related products
Aluminum wall oval pool PS SQ 6.00 x 3.20 x 1.50 m aluminum handrail…
4,84 €
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 23.5 m³. General information on aluminum-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing mesh, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection of the...
Pool cover MTH Air Protect UNI gray oval-eight shape …
617,10 €
For optimal pool protection in winter, choose the inflatable AIR PROTECT PROFI cover for oval and figure-eight pools. Both the top and bottom surfaces are made of fabric-reinforced PVC, each weighing 580 g/m². When inflated, this double-layered cover forms a uniform dome over the pool. This provides optimal protection, preventing rainwater, dirt, and even snow from entering your pool. A valve inlet adapter with a 20 mm diameter nozzle is included.
PS30 rectangular pool POOLSANA 6.00 x 3.00 x 1.50 m 4D foil…
4,84 €
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 25 m³, number of insulating formwork blocks: 95 pieces, each 100 x 25 x 30 cm (L x W x H), including end caps for the corners. General information on polystyrene rectangular pools: The hollow insulating blocks must be installed bonded to a reinforced concrete slab, reinforced with rebar, and filled with concrete. The rectangular pool is primarily designed for complete in-ground installation. For partial in-ground installation, the reinforcement may need to be adjusted.
PURE stainless steel pool ladder, narrow/wide 3-step
246,84 €
narrow-profile swimming pool ladder made of V2A stainless steel with a 43 mm diameter stiles, offering excellent value for money. On the inside of the pool, the stiles are fitted with plastic buffers that support the ladder against the pool wall without chafing the liner. On the outside of the pool, the ladder is secured using plastic mounting sleeves that are cemented flush with the ground and serve as anchor points for the ladder stiles. Alternative...
Rectangular pool 7.00 x 3.50 x 1.50 m PLUS set sand under…
7,26 €
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 34.5 m³, number of insulating blocks: 110 pieces, each 100 x 25 x 30 cm (L x W x H), including end caps for the corners. General information on polystyrene rectangular pools: The hollow insulating blocks must be installed bonded to a reinforced concrete slab, reinforced with rebar, and filled with concrete. The rectangular pool is primarily designed for complete in-ground installation. For partial in-ground installation, the type of reinforcement may need to be adjusted...
Round pool Alu PS SQ 3.00 x 1.25 m Alu handrail 0.9 mm …
2,42 €
Pool depth 125 cm, water depth approx. 110-115 cm, capacity approx. 8 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size.
Single pool steel wall round pool POOLSANA PQ 4.50 x 1.35 m
1 621,40 €
Pool depth 135 cm, water depth approx. 120-125 cm, capacity approx. 20 m³. General information on steel-walled round pools: All round pools (1.20 m and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size or...
Steel wall oval pool POOLSANA HQ 6.00 x 3.20 x 1.20 m PROFI…
2,42 €
Pool depth 120 cm, water depth approx. 105-110 cm, capacity approx. 18.5 m³. General information on steel-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing mesh, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection...
