Pool liner 0.8 mm for oval pools, grey
689,70 €
Pool Liner Made in Germany: This pool liner is manufactured in Germany in compliance with the highest quality standards. From the production of the raw material into liner sheets to the finishing and welding together to create a complete pool lining, this pool liner guarantees you exclusively quality Made in Germany. The work is carried out by skilled professionals, some of whom have decades of experience. As a testament to our own conviction…
Related products
Aluminum wall oval pool PS SQ 5.25 x 3.20 x 1.50 m with aluminum handles…
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 20.5 m³. General information on aluminum-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing mesh, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection of the...
Aluminum wall round pool PS HQ with aluminum handrail 4.50 x 1.25 m PLU…
Pool depth 125 cm, water depth approx. 110-115 cm, capacity approx. 18 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required regardless of the pool size...
PREMIUM underlay fleece, pack IV 36 m², quality 500 g/m²
Very strong, thermally and mechanically bonded, rot-proof underlay fleece for protecting the pool liner from PVC-incompatible materials, min. 500 g/m². Recommended for the following swimming pools from our range: Round pool 6.00 m, Oval pool 7.50 x 3.50 m, Oval pool 8.00 x 4.00 m, Figure-eight pool 7.25 x 4.60 m. The fleece is supplied in rolls 2 m wide and 18 m long. Due to manufacturing and packaging reasons, the fleece cannot always be delivered in one piece.
Rectangular pool 6.00 x 3.00 x 1.50 m PROFI set high level …
Pool depth 150 cm, water depth approx. 142-144 cm, capacity approx. 25.5 m³, number of insulating blocks: 95 pieces, each 100 x 25 x 30 cm (L x W x H), including end caps for the corners. General information on polystyrene rectangular pools: The hollow insulating blocks must be installed bonded to a reinforced concrete slab, reinforced with rebar, and filled with concrete. The rectangular pool is primarily designed for complete in-ground installation. For partial in-ground installation, the type of reinforcement may need to be adjusted.
Round pool Alu PS HQ 4.00 x 1.25 m Alu handrail 0.8 mm …
Pool depth 125 cm, water depth approx. 110-115 cm, capacity approx. 14.5 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, a concrete base slab is required – regardless of the pool size…
Sand filter system POOLSANA Plus 300Pump 75
Heavy-duty and pressure-resistant filter tank Made in Germany. The sand filter tank with a diameter of 300 mm is made of polypropylene and is particularly impressive due to its high-quality workmanship and high pressure resistance of up to 1.5 bar. In combination with the self-priming, plug-and-play pool pump, which has a circulation capacity of approximately 6 m³/h at 6 mWs, 450 watts, 230 V, the system is very well suited for swimming pools up to approximately 30 m³. Filling capacity...
Sand filter system POOLSANA PREMIUM 500 with POOLSANA Pump 100
Maximum convenience thanks to the two-part tank design. The centrally divided design makes filling and changing the sand particularly easy, making the system ideal for installation in confined spaces such as basements or filter shafts. The two tank halves are connected by a stainless steel clamping ring, which is finished with a visually appealing black protective coating. The tank is made of GRP (glass-reinforced plastic)...
Steel-walled figure-eight pool PS HQ 6.25 x 3.60 x 1.20 m liner…
Pool depth 120 cm, water depth approx. 105-110 cm, capacity approx. 22.5 m³. General information on steel-walled figure-eight pools: All figure-eight pools (1.20 m and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. A base slab is required for all figure-eight pools, into which the included steel support structure, consisting of two side supports and one...