50 mm piping set for floor drain
135,52 €
Complete 50 mm piping kit for connecting the floor drain to the suction line. Consisting of: 1 x roll of SpaFlex hose 50 mm (12 m), 1 x 1.5 m PVC pipe 50 mm, 1 x 2-way ball valve 50 mm, 2 x 90° elbows 50 mm, 1 x T-piece 50 mm, 1 x adapter 2″ male thread x 50 mm, 2 x pipe clips, 1 x PVC cleaner, 1 x PVC adhesive, 1 x roll of Teflon tape
Related products
POOLSANA UV-C disinfection device PROFI 75W stainless steel
The POOL SANA UV disinfection unit is integrated into the filter circuit between the sand filter system and the inlet nozzles. The physically cleaned water coming from the sand filter system is exposed to a high dose of short-wave UV-C radiation (253.7 nm) in the disinfection unit, which kills almost all bacteria, viruses, and even mold spores. This can reduce the need for water treatment chemicals by up to 80%. If the disinfection unit is in operation for at least 8-10 hours daily...
PS3080 rectangular pool POOLSANA HQ 6.00 x 3.00 x 1.50 m…
Pool depth 150 cm, water depth approx. 142-144 cm, capacity approx. 25.5 m³, number of insulating blocks: 95 pieces, each 100 x 25 x 30 cm (L x W x H), including end caps for the corners. General information on polystyrene rectangular pools: The hollow insulating blocks must be installed bonded to a reinforced concrete slab, reinforced with rebar, and filled with concrete. The rectangular pool is primarily designed for complete in-ground installation. For partial in-ground installation, the type of reinforcement may need to be adjusted.
Round pool Alu PS SQ 3.00 x 1.25 m Alu handrail 0.9 mm …
Pool depth 125 cm, water depth approx. 110-115 cm, capacity approx. 8 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size.
Single pool, aluminum wall oval pool PS HQ 7.00 x 3.50 x 1.50 m …
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 30.5 m³. General information on aluminum-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing steel, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection of the...
Single steel-walled round pool PS SQ 4.50 x 1.50 m with A…
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 22 m³. General information on steel-walled round pools: All round pools (1.20 m and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size or...
Steel wall round pool POOLSANA HQ 4.00 x 1.50 m PLUS set…
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 17.5 m³. General information on steel-walled round pools: All round pools (1.20 m and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size – and...
Steel-walled figure-eight pool PS HQ 4.70 x 3.00 x 1.35 m with aluminum…
Pool depth 135 cm, water depth approx. 120-125 cm, capacity approx. 17.5 m³. General information on steel-walled figure-eight pools: All figure-eight pools (1.20 m and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. A base slab is required for all figure-eight pools, into which the included steel support structure, consisting of two side supports and one...
Underlay fleece, pack IV, 36 m², quality 300 g/m²
Very strong, thermally and mechanically bonded, rot-proof underlay fleece for protecting the pool liner from PVC-incompatible materials, min. 300 g/m². Recommended for the following swimming pools from our range: Round pool 6.00 m, Oval pool 7.50 x 3.50 m, Oval pool 8.00 x 4.00 m, Figure-eight pool 7.25 x 4.60 m. The fleece is supplied in rolls 2 m wide and 18 m long. Due to manufacturing and packaging reasons, the fleece cannot always be delivered in one piece.