Single round pool PS HQ 3.00 x 1.25 m with aluminum wall…
1 933,58 €
Pool depth 125 cm, water depth approx. 110-115 cm, capacity approx. 8 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required – regardless of the pool size.
Description
Round pool POOL SANA HQ – Made in Germany – consisting of a 1 mm thick aluminum wall in silver-grey/white aluminum + very precisely fitting, sand-colored PVC pool liner 0.8 mm with hanging bead + combination special handrail made of high-quality and stable aluminum and bottom rails made of plastic.
Related products
Pool pump POOLSANA Pump 75
Self-priming, reliable pool pump. The POOLSANA Pump 75 impresses above all with its compact design and very high reliability. This TÜV and GS-certified, self-priming pool pump features a pre-filter basket, a drain unit, and comes pre-equipped with a power cable and plug. The pump has a circulation capacity of 6 m³/h at 6 mWS and is ideally suited for swimming pools up to approximately 25 m³ water capacity or for filter tanks with a capacity of...
PoolSANA InverPOWER ULTRA 12 Full Inverter Heat Pump
1. Ultra-high energy efficiency. The name says it all. Thanks to full inverter technology combined with sophisticated design and control, our InverPOWER ULTRA heat pumps have a particularly high COP (coefficient of performance) of over 18, setting completely new standards in efficiency, as their heating output is many times higher than the power they draw from the grid. But the exterior is also impressive. The casing of the InverP...
PREMIUM underlay fleece, pack IV 36 m², quality 500 g/m²
Very strong, thermally and mechanically bonded, rot-proof underlay fleece for protecting the pool liner from PVC-incompatible materials, min. 500 g/m². Recommended for the following swimming pools from our range: Round pool 6.00 m, Oval pool 7.50 x 3.50 m, Oval pool 8.00 x 4.00 m, Figure-eight pool 7.25 x 4.60 m. The fleece is supplied in rolls 2 m wide and 18 m long. Due to manufacturing and packaging reasons, the fleece cannot always be delivered in one piece.
Single pool aluminum wall oval pool POOLSANA SQ 5.25 x 3.20 x 1…
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 20.5 m³. General information on aluminum-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing mesh, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection of the...
Single round pool PS HQ 4.50 x 1.50 m with aluminum wall…
Pool depth 150 cm, water depth approx. 135-140 cm, capacity approx. 22 m³. General information on aluminum-walled round pools: All round pools (1.20 m, 1.25 m, and 1.35 m) can be installed freestanding or partially or fully in-ground. For the 1.50 m pool, however, partial in-ground installation of at least 50 cm is mandatory. Please note that the in-ground area of the pool must always be backfilled with lean concrete. Furthermore, the construction of a concrete base slab is required regardless of the pool size...
Steel wall oval pool POOLSANA HQ 4.90 x 3.00 x 1.35 m PLUS set
Pool depth 135 cm, water depth approx. 120-125 cm, capacity approx. 16 m³. General information on steel-walled oval pools: The oval pools are not freestanding and must be installed to a depth of at least 23 cm of their total height. A concrete base slab and retaining walls along the long sides, which must be connected to the base slab with reinforcing steel, are required on-site. After installation, the ends of the oval pool are backfilled with lean concrete. For disinfection of the...
Swimming pool skimmer MTH SK 2.1 unglued special…
Hanging skimmer specifically for frame pools. With our new MTH SK 2.1, you get an extremely robust and durable hanging skimmer for your frame pool. The kit consists of the external body, the internal skimmer unit, two 90° elbows, two spacers, and two pipe sections, each approximately 29 cm long. Depending on the handrail width, the pipe sections can be cut to size, and the connection between the body and skimmer can be made to ensure the hanging skimmer is optimally positioned.
Underlay fleece PREMIUM Pack I 15 m², quality 500 g/m²
Very strong, thermally and mechanically bonded, rot-proof underlay fleece for protecting the pool liner from PVC-incompatible materials, min. 500 g/m². Recommended for the following swimming pools from our range: Round pools 3.00 m, Round pools 3.50 m, Round pools 3.60 m. The fleece is supplied in rolls 2 m wide and 7.5 m long. Due to manufacturing and packaging reasons, the fleece cannot always be supplied in one piece; a maximum of two sections will be provided.